Production
Eurosens MWS universal liquid level sensor
Universal distance sensors Eurosens MWS are used for non-contact distance measurement to the nearest object or to the surface of a liquid. A distinctive feature of the sensor is the ability to measure through obstacles that are transparent to electromagnetic waves (plastic). Typical application is liquid level measurement.
- Level measurement of liquids, conversion to volume according to a programmable calibration table.
- Measuring the distance to the object.
- Volume measurement of bulk solids recalculated from height according to a programmable calibration table.
- Possibility of measuring the liquid level through the top surface of the tank without a immersion (plastic and other materials transparent to electromagnetic waves).
Wireless tilt angle sensor Eurosens Degree Bt
The Eurosens Degree Bt wireless tilt angle sensor is designed to measure the angular position of parts and mechanisms relative to the gravity vector and transmit this data over a 2.4 GHz radio channel Bluetooth Low Energy (BLE). The sensor is self-powered from a built-in battery.
The sensor measures 3 tilt angles of the coordinate axes relative to the gravity vector. Pay attention to the possibility of measuring various deviations of the object – measurement is possible only if the position of the sensor changes relative to the gravity vector.
The sensor transmits the measured values of 3 angles relative to the gravity vector using the BLE protocol and is compatible with such GPS tracking devices terminals as Teltonika, SMART (Navteletom), Neomatica, Fort-Monitor and others. Check compatibility with our technical support. Sensor sends these parameters to a GPS tracker over BLE-protocol: Angle X, Angle Y, Angle Z, number of events, number of chains,
Name of parameter | Value |
Radio frequency | 2,4 GHz |
Battery voltage | 3 … 3,7V |
Data interface | Bluetooth Low Energy (BLE) |
Sensitivity of receiver /power of transmitter | -96 дБм / +4 дБм |
Data protocol | Advertising-packet (see Appendix 1) |
Connection range (in direct visibility) | 10 meters |
Tilt angle measurement error | ±1° |
Temperature measurement error | ±1°C |
Number of records of events (for devices with datalogger function) | 900 |
Operation temperature range | – 40 … + 85 0С |
IP protection class | IP67 |
Dimensions | 100 х 54 х 34 |
Weight, kg | 0,3 |
In addition to measuring the tilt angles, the sensor determines Events and Chains of events. An event is detected when angle have gone beyond the specified boundaries. One event can be configured for each of the axes (X, Y, Z). When an event occurs, the event counter is incremented by one. A chain of events is the fulfillment of the conditions of a sequence of events separated by time intervals. For each of the events, an axis of angle measurement, an angle value and a comparison type (<,>) are specified. The maximum waiting time for the next condition is also set.
When a chain of events is executed, the chain counter is incremented by one. The numbers of events and event chains are transmitted over the BLE protocol. So you don’t need to process X,Y,Z angle values in your tracking software to detect an event. Moreover frequent data transmission could drain the battery. We recommed to setup the internal event/chain of events detection engine to avoid missing the important events. Eurosens Degree Bt can be configured with smartphone with Bluetooth with installed Eurosens Degree Bt configurator.
Sensor supports 3 different operation modes.
Mode 1. General tilt angle monitoring and event/events chain detection
Mode 2. Drum rotation sensor monitoring (typical application is monitoring of concrete delivery truck with rotating drum. RPM and direction of drum rotation are measured.
Mode 3. Boom operation monitoring, real operation hours measurement.
Eurosens InCAN
Is used for contactless connection to the vehicle CAN bus. May be used at cars, trucks, buses, agriculture and special machinery. Secures safety of the vehicle CAN bus operation.
Compatible with all GPS trackers with CAN bus interface
Eurosens DDS CAN sensor
Eurosens DDS CAN sensor is used on the trucks with leaf spring suspension to detect actual axle load.
Eurosens DDS CAN with mounting kit converts the suspension deflection under load to axle load value in tons. Mounting kit comes with sensor.
After installlation the calibration of sensor is required. Calibration can be performed with a help of platform scales.
Eurosens DDS RS sensor
Eurosens DDS RS sensor is used on the trucks with leaf spring suspension to detect actual axle load.
Eurosens DDS RS with mounting kit converts the suspension deflection under load to axle load value in tons. Mounting kit comes with sensor.
After installlation the calibration of sensor is required. Calibration can be performed with a help of platform scales.